Dive Gear Express Logo
Free Shipping
on qualifying orders
Contact Us Shipping  |  Returns
 
  Home

CCR Cylinders and Valves

Pricelist  [Currency] 

We offer CCR Cylinder Sets configured for use with closed circuit rebreathers. They are aluminum or steel, preconfigured for use as oxygen and diluent in your choice of sizes and valves. We ship your cylinder with the valve installed (domestic ground US only), but during shipping the valve may loosen at the neck, so prior to the initial fill the valve should be made as tight as possible by hand only. The cylinders have a current month Visual Inspection Sticker, therefore no reinspection is necessary before filling. SCUBA Tanks must be hydrostatically tested every five years (60 months). Small cylinders are not frequently manufactured and typically have a factory hydro date between 6 and 18 months old, but can be older for sizes very rarely manufactured such as the AL-20 or LP-27.

CCR Cylinder Sets

  • Cylinder Pair (Both Oxygen Clean)
  • Travel Caps for Cylinder Necks
  • Valve Pair (Black & Green Knobs)
  • Dust Plugs for Valves
  • Contents Decals (Oxygen & Diluent)
  • VIP Decals (Both Marked for O2 Service)
The valves are configured by default as shown: the oxygen cylinder is on the diver's right, with the outlets facing away from diver. Or if you prefer a different configuration, give us your detailed specifications in the special instructions at checkout. Let us know what rebreather model you are using, whether you want the oxygen cylinder on the diver's left or right, with the valve outlets facing away from or toward the diver. However, both cylinders and valves are oxygen clean and the decals are shipped loose, so if you decide to configure them differently, you can change the orientation yourself just by swapping the handwheels.

> CCR Pair of AL Cylinders w/Left+Right Valves
+ Enlarge

In Stock

> CCR Pair of AL Cylinders w/Left+Right Valves

This pair of brushed no-coat aluminum cylinders is preconfigured for rebreather use as the oxygen and diluent cylinders, in your choice of size. (The 3L AL-20 set is pictured; see the table below for all cylinder specifications.) Both cylinders are oxygen clean with oxygen compatible valves. The oxygen cylinder has a green handwheel and the diluent cylinder has a black handwheel. Also available as a low cost option are the Vindicator Safety Handwheels. Included in the CCR cylinder package are a green and white OXYGEN decal and a red and white DILUENT decal. The cylinders have a current month Visual Inspection Sticker; no reinspection is necessary before filling.


> CCR Pair of Steel Cylinders w/Left+Right Valves
+ Enlarge

In Stock

> CCR Pair of Steel Cylinders w/Left+Right Valves

These are a pair of cold gavanized white steel cylinders, preconfigured for rebreather use as the oxygen and diluent cylinders, in your choice of size. (See the table below for all cylinder specifications.) Both cylinders are oxygen clean with left and right hand oxygen compatible valves. Choose from pairs of left and right valves by Blue Steel, Dive Rite or Thermo. The oxygen cylinder has a green handwheel and the diluent cylinder has a black handwheel. Also available as a low cost option are the Vindicator Safety Handwheels. Included in the CCR cylinder package are a green and white OXYGEN decal and a red and white DILUENT decal. The cylinders have a current month Visual Inspection Sticker, thus no reinspection is necessary before filling. Note the 3L cylinders (but not the 2L) are available in a choice of white or black finish color.


> CCR Pair of Steel Cylinders w/Inline Valves
+ Enlarge

In Stock

> CCR Pair of Steel Cylinders w/Inline Valves

This pair of cold gavanized steel cylinders, in your choice of size, is preconfigured for rebreather use as the oxygen and diluent cylinders. (See the table below for all cylinder specifications.) Both cylinders are oxygen clean with inline T valves for use with the Inspiration, Evolution, Sentinel or rEvo rebreather. Choose either the OEM inline valves by Ambient Pressure Diving or a functionally equivalent value priced inline valve by Blue Steel. The oxygen cylinder has a green handwheel and includes a green and white oxygen decal. The diluent cylinder has a black handwheel and includes a red and white diluent decal. Labels are shipped loose so that you may apply them in the appropriate position. The cylinders have a current month Visual Inspection Sticker; no reinspection is necessary before filling. Note the 3L cylinders (but not the 2L) are available in a choice of white or black finish color.



Tek Tip Tek Tip Symbol

Advice for Traveling with Rebreather Cylinders

Regardless of the brand of rebreather it can be annoying to travel with cylinders because they are carefully examined by security personnel, and occasionally even confiscated. TSA says cylinders are allowed in checked baggage only if the cylinder has an open end. This means you must remove the valve and you must not plug the cylinder opening. Nothing should obscure the cylinder opening, not even clear tape or a plastic bag. This also means the open cylinders that traveled with you in checked baggage are contaminated and no longer suitable for oxygen service. Have a plan for how you are going to have them oxygen cleaned at the destination. Consider taking the cylinders with you as carry-on baggage, where you can remove a travel cap yourself during security inspections. You may prefer to rent cylinders at the destination or ship the cylinders ahead by a package carrier which will allow the cylinders to be sealed during transport.


Rebreather Gas Cylinder Specifications

Cylinder Service
Pressure
(psi)
Diameter
(inches)
Height*
(inches)
Weight
Empty
(pounds)
Buoyancy*
Full : Empty
(pounds)
Finish
Aluminum 13 (Catalina 2L) 3000 4.38 13.1 6.0 - 1.7 : - 0.7 Brushed
Aluminum 19 (Catalina 3L) 3000 4.38 18.6 8.2 - 1.4 : + 0.1 Brushed
Aluminum 20 (Hy-Mark 3L 04/10) 3000 5.25 13.8 9.2 - 1.4 : - 0.0 Brushed
Steel 15 (Faber 2L) 3442 3.94 14.2 6.6 - 2.4 : - 1.2 White
Steel 23 (Faber 3L) 3442 3.94 19.5 8.6 - 2.6 : - 0.7 White
Steel 23 (Faber 3L) 3442 3.94 19.5 8.6 - 2.6 : - 0.7 Black
Steel 27 (Faber 4L 07/08) 2400+ (2640) 5.5 14.5 11.9 - 3.0 : - 1.0 White

* Height/Weight is cylinder only, i.e. less valve. All values are approximate.
* Bouyancy is calculated with standard K valve in seawater.
Cylinder set would be slightly more negative with the supplied modular valves.

Related Products

Pricing for Rebreather Cylinders and Valves

Cylinder prices do include FREE continental U.S. domestic shipping.

Cylinder prices do NOT include international shipping. Our cylinders and valves are Imperial 3/4 NPS neck threads, NOT Metric M25 neck threads, and the valves have overpressure relief devices. The cylinders have US DOT and Canadian CTC markings suitable for use only in North America. Our cylinders and valves are NOT CE approved and NOT suitable for use in the European Union.

Image Item SKU Description Ship Status US $ Price
[]

  Individual Cylinders for CCR  
 SPM-AL-13CCR Worthington Aluminum 13 (2L) Cylinder
In Stock  $129.00
 SPM-AL-19CCR Worthington Aluminum 19 (3L) Cylinder
In Stock  $139.00
 ZGL-AL-20CCR Hy-Mark Aluminum 20 (3L) Cylinder
In Stock  $139.00
 BSL-FX15CCR Blue Steel Faber FX-15 (2L) Cylinder, white
In Stock  $179.00
 BSL-FX23CCR-WHT Blue Steel Faber FX-23 (3L) Cylinder, white
In Stock  $189.00
 BSL-FX23CCR-BLK Blue Steel Faber FX-23 (3L) Cylinder, black
In Stock  $189.00
 BSL-LP27CCR Blue Steel Faber LP-27 (4L) Cylinder, white
2-3 Days  $199.00
  Valves for Rebreather Cylinders  
B/S Valve, Pro DIN/K, Left  BSL-10108 B/S Valve, Pro DIN/K, Left In Stock Sale! $45.00
 $39.95
B/S Valve, Pro DIN/K, Right (typical side)  BSL-10120 B/S Valve, Pro DIN/K, Right (typical side) In Stock Sale! $45.00
 $39.95
DR Modular Valve, Pro DIN/K, Left (typical side)  DR-VA3001L-200 DR Modular Valve, Pro DIN/K, Left (typical side) In Stock  $59.00
DR Modular Valve, Pro DIN/K, Right  DR-VA3001R-200 DR Modular Valve, Pro DIN/K, Right In Stock  $59.00
TV Modular Valve, Pro DIN/K, Left  SPM-TV8043LH TV Modular Valve, Pro DIN/K, Left In Stock  $90.00
TV Modular Valve, Pro DIN/K, Right (typical side)  SPM-TV8043RH TV Modular Valve, Pro DIN/K, Right (typical side) In Stock  $90.00
TV Handwheel, Green, rubber ribbed (6)*  SPM-TV5240-6AN TV Handwheel, Green, rubber ribbed (6)* In Stock  $5.49
B/S Inline CCR Valve, Black  BSL-18040-BH B/S Inline CCR Valve, Black In Stock  $55.00
B/S Inline CCR Valve, Green  BSL-18040-GH B/S Inline CCR Valve, Green In Stock  $55.00
APD Inline CCR Valve, Black  SDS-RB13B APD Inline CCR Valve, Black In Stock  $120.00
APD Inline CCR Valve, Green  SDS-RB13C APD Inline CCR Valve, Green In Stock  $120.00
  Cylinder Accessories  
Diluent Decal, 10-Inch x 3-Inch  SPM-D-DILUENT Diluent Decal, 10-Inch x 3-Inch In Stock  $5.00
Oxygen Decal, 10-Inch x 3-Inch  SPM-D-OXYGEN Oxygen Decal, 10-Inch x 3-Inch In Stock  $5.00
Threaded Dust Plug for DIN Valve, Plastic  DX-70135 Threaded Dust Plug for DIN Valve, Plastic In Stock  $3.95
 DX-70902 Threaded Dust Plug for DIN Valve, Delrin In Stock  $9.99

All Dive Gear Express financial transactions are in United States Dollars (US $).
Prices in currencies other than US $ are approximations and should be used as a guide only.

Having trouble finding something?
Try using our Google custom search engine:
Customer Support Still having trouble?
Talk to our people, like Joyce:

Contact Us via e-mail or telephone
We'll see what we can do to help you.
Your complete satisfaction is our goal.
Dive Gear Express is an authorized dealer for all of the new, first quality, genuine brand name scuba diving equipment we sell.

 

About Us  |   Contact Us  |   Ordering  |   Returns  |   Shipping


BCs  |   Computers  |   Drysuits/DPVs  |   Fins/Masks  |   Gas/Tanks  |   Hardware  |   Lights  |   Manuals  |   Rebreathers  |   Regulators/SPGs  |   Tools
Small Clear Image

© Copyright 2012   |   Terms & Conditions   |   Privacy Statement

Convert e-commerce currencies